Pages

Sunday, December 20, 2009

How to care for Canon Printer Ink tank

How to take care Canon Printer Ink tank

If you use the printer canon BJC 2100, S 200 SPX, canon i 320, pixma IP 1000 or i6100 printer canon A3 and the like? In the history of canon printer, serial printer uses cartridges with printhead models and inktank separately. Some users prefer to use a model like this cartridge model. Problems that often happens is that it printhead total dead end and are required to purchase new cartidge. Why?

There are 3 reasons why cases like the above.

  1. Foam on the tank was saturated ink that will not absorb ink refill. This means that if forced direfill, ink flows like water flowing in a solid. Certainly very little that can be stored into the foam inktank. The result is predictable, ink tanks and the lack of printing ink was not optimal, or would not print at all.
  2. Foam surface was crusty ink tank or often due to long use. Despite direfill, transport of ink from the printhead inktank cork hindered by this scale.
  3. Position shifts foam than necessary, so that transportation of ink broken / or not well.
The solution if the result is less maximum print is by soaking a few minutes the printer printhead cleaner and replace the liquid ink tanks with new ones. Guaranteed results returned to normal print.
Readmore »» How to care for Canon Printer Ink tank

Some Ways to Reset the Printer Canon

A. Reset Printer Canon Pixma iP1000, iP1500
For canon pixma ip1000, iP1500, before using the software reset, you must to manually reset
Step 1: Reset manually
  • Disconnect the power cable and USB cable. Unplug power and USB.
  • Open the printer front cover, press and hold the power button.
  • Replace the power cable to the electricity.
  • Close the front cover of the printer and release the power button.
  • Reconnect kebel usb printer to the computer.
Step 2: Using Software resetter
  • Download software resetter used for Canon Pixma iP1000, iP1500
  • Run resetternya software, and select customized with Usb port printer port.
  • Select SET DESTINATION 1 and the printer is in reset.
  • To ensure the printer is normal, use to print.
B. Reset Printer Canon iP1300 iP 1700 and In the Printer Canon iP1300 iP 1700 and reset the way there are two methods of manual reset and reset by using the software.
Step 1: Reset manually
  • Turn off the printer or the Canon Pixma iP1700 Canon Pixma iP1300
  • Press and hold the resume button and press the power button.
  • Keep hold the power button, a resume button is released.
  • Press the resume button 2 times then release all buttons.
  • green light comes on and stop blinking.
  • When the green led is constantly on (not blinking) press the resume button 4 times.
  • Press the power button to turn off the printer, if you do not want to die press the power button again.
  • kalu finished printer canon iP1700 or iP1300 usually back to normal, if still blinking can be repeated again.
Step 2: Reset using software resetter
  • Download software resetter used for the Canon iP1300 and iP1700 Printers
  • Extract the new resetter files downloaded.
  • Ensure that all file attributes from Read Only free (in some trials sometimes software does not work with a good if there is still read only)
  • Run GeneralTool.exe
  • In USB Port select the port your printer is detected.
  • Click the Lock Release
  • Select (check) EEPROM CLEAR.
  • Provide blank paper to print. Then Click the Test Pattern 1
  • Finish iP1700 Printer IP1300 and you are back to normal.
C. Reset Canon Pixma iP1200, iP1600, iP2200
  • Download software for Canon iP1200, iP1600, 2200 (Printers.DOWNLOAD Service Tool Software for Printer Canon Pixma iP1200, iP1600, iP2200)
  • Extract the files downloaded.
  • Run GeneralTool.exe
  • Select the connected USB port number from USB PORT
  • Click LOCK RELEASE, and select the printer model in the SET DESTINATION
  • In CLEAR WASTE INK COUNTER, select MAIN or platen to reset the counter on the printer ink. MAIN is used to reset the main waste ink counter is platen to platen waste ink counter
Readmore »» Some Ways to Reset the Printer Canon

How to Safely Use Toner

Safe way to clean or replace the Toner Catridge

If you are cleaning or replacing the toner cartridge on your own, there are several safe ways to watch and prevention of risks. Here are some tips on how to hold the toner cartridge or laser printer.

Position the toner in place of the flat and flat as toner powder is very soft and easy to spill. If the spill powder flying in the air, so may be inhaled and can endanger your health. We recommend using a mask every time the toner cartridge for holding a mask can protect the lungs from inhaling toner particles when the powder spilled toner. If you find the powder spilled toner, turn off the fan, Air Conditioner, or other equipment that can carry toner powder. Leave the room and returned a few minutes after the toner powder has disappeared
Readmore »» How to Safely Use Toner

How to save Toner

Learning from some experience and the literature, the following 10 ways to get more save ink and toner cartridges. Because of printer ink and toner is very important and not free. Besides, also need to save the print materials such as paper and electrical energy to run the printer in order to practice the habits of life eco-friendly (friendly to nature, and use of natural resources and energy as needed).
  1. Use Ecofont (Font economical and eco-friendly for the printer)
    There are the types of letters or fonts that are helpful than others, because these fonts need less ink or toner in the print paper. Ecofont font was developed by SPRANQ, have the ability to save 20% ink-print compared with other standard fonts. These fonts can be downloaded for free at ecofont website and read the instructions on how to install these fonts in Windows XP, Vista, Mac OS X and Linux.
    In addition to using the font, it can save is by reducing the amount of text bold, use a smaller font and simply write what is important for printing.
  2. Be sure to print the text is correct all, revisions if there are errors before printing.
    Do not print anything before revising the manuscript of the writing errors, it can reduce printing useless.
  3. Choosing what you need to be printed
    Print only the required course of the entire book and not have to print the entire book.
    Examples:
    If you want to print text without a picture, you can use the print option "Draft output", which will help to print faster with low-quality coffee draft without images.
  4. Print You Like (website optimization that will in print)
    Basically, this command form of online website editor, who can help you to optimize other websites in print, by reducing local and white ads, to print what you need. for details click this web address http://www.printwhatyoulike.com/.
    This service is easy, simply visit the website, enter the URL of the page that you want to print, for example this article, and then click start and start editing, including the background or the part that you think does not really matter.
  5. GreenPrint (Software Industrial Inkjet Printer)
    GreenPrint is a software for Windows and Mac OSX are also capable of analyzing the print job you are doing and tell you your potential waste of printed material, so you can reduce the pages you do not want. In addition, you can print PDF files without using ink. In addition, GreenPrint also help calculate the amount of paper you save. Source: http://www.printgreener.com/
  6. Printer Settings
    Setting an appropriate printer is very important and will help save many Andauntuk printed material if you do it properly. In addition to manually select the setting "low quality" for each print job, you can also use the "low quality" as the default print. And you can change it manually if you want "high quality", so you can choose if you need it.
    To permanently change the default printer, select the printer settings on your OS settings, and follow the ways of the following:
    • Layout Print: select whether you want to choose to print on both parts of a page or one side only as needed, for example, you print a lot of read-only, you can choose the two parts of a page.
    • Print in black ink and white mode.
    • Reduce the resolution: On some printers there is the option to reduce the image resolution, this option is usually found in the advanced setting your printer. 300 dpi is sufficient for many purposes, besides that most types of paper can not be printed in high resolution. So use high resolution only for the paper can be accepted, sepertiu high quality photo paper (high-quality photo paper).
  7. Print Preview
    Before printing, print preview and check beforehand to be sure that all have the desired fit. From here you can choose to print several pages on one sheet of paper, reduce the image size and so forth.
  8. Printer Settings (for inkjet)
    Check the printer manual to see recommendations from the printer manufacturer. In addition, some of the tips below can be useful.
    • Keep electrical current still flows, because the printer requires a steady electric current. If you do not connect the cable to the electric current, when turned on again, this printer will clean themselves. This process if repeated every day, would spend a lot of energy and ink.
    • Turn on and turn off the printer by using the on / off just so that you use the ink was not dry quickly.
  9. Age Toner
    For laser printers, toner cartridge shuffle could be done if forced to extend the usage.
  10. Print until the ink is completely discharged
    Printing to print a complete stop, because it can prolong the life of your cartridge or printer.
Readmore »» How to save Toner

How To Care for Dot Matrix Printer

To Care printers dot-matrix type if you know how actually quite easy. The steps you need to do is remove the ribbon or ink cartridges, and then watch how the tape moves past the print head. Another thing to note, that you can clean the print head dot-matrix using a special tool. Facility consists of a cleanser that is inserted through the printer as if a paper and cleaning solution. So you need to do is wet the sheet with a solution, then run the printer to print on it (without a ribbon) while for the test. Where the solution was to dissolve the remnants of the dry ink, and then absorbed by the sheet.

Or you can do other way by using a special cleaning cartridge is inserted as a replacement. In addition, you also need to clean the platen (a rubber cylinder) to remove the remaining ink when the paper was printed. Perform tests to check the printer, so that satisfactory printing quality.

From the general steps in the process can be explained in detail as follows:
  1. Turn off the printer, remove the lid and ribbon.
  2. Clean dust or dirt on the printer.
  3. Check and clean the streets and out of the paper and platen.
  4. Clean and replace the 'head' print.
  5. Replace the ribbon if it is finished.
  6. Do a test print to get a satisfactory print quality.
  7. Clean and return the printer cover.
  8. Perform examination paper and make sure installed properly and smoothly entry conditions.
Readmore »» How To Care for Dot Matrix Printer

How To Longer Age Printer

The existence of the printer as printing the current document is a primary requirement for companies large or small scale. Printer conditions often result in less attention to short-age of the printer. Actually there is an easy way to extend the age of the printer, here are some maintenance tips to keep it durable printers even though he was old.

Paper Case Clock
When the print process is in progress occurs paper jam (paper jam), is not advisable to pull the paper forcibly contained in the printer. Because it can leave the pieces of paper on the inside that will cause damage to the printer. If this happens, which can be done by removing the cover adalan printer and then slowly rotate the wheel of paper (paper wheel) until the condition of paper out of all.

Turn off the printer
Always turn off the printer when not in use. This can prevent the closing of the holes flow of ink in the printer head. Another advantage is that it can prevent the ink dry faster and can optimize the performance and function of the printer. Always use the power button when turned off the printer, and if necessary disconnect from the electric power to make it more secure.

Avoid toner / ink cartridges cheap
We have sold a lot of toner / ink cheap refiil that can be used to modify the printer. Toner / ink like this is very often mengirit expenditure when using the printer to print. However, the influence of the use of toner / ink is very bad modification to the printer durability. Therefore, if you want the printer preserved even though he was dusk, it is advisable to use toner / ink that has the optimal qualities such as Eikona ® or Qualiva ®. In addition to not lose quality with original warranty, too.

Cartridge
Printer cartridge filled with delicate electronic link. This thing is very vulnerable damage if treated carelessly. It could be data from a computer does not go up and cause the print was not optimal. Therefore, the cartridge must be treated cautiously. Cartridge durability also varies, depending on how often the process of printing. Some users simply replace the two or three times a year, while not a few who change the cartridge every few months. Cartridge is left mounted on the printer and never used too long can dry out. To prevent a decline in print quality, use the printer periodically.

Clean Dirt
Clean the inside of the printer every one or two weeks, depending on how often to use the printer. This will keep the printer in the printing capabilities. Do not forget to observe whether there are items left in the printer. Do not store the printers and dusty place full of insects. If it is a dusty place, it's good printer with plastic wrap to protect it from dirt.

Diagnostic Tools
Each printer has a diagnostic software tool to treat or deal with problems regarding tsb printer. Take time to learn. Might provide information that could help overcome the problems in the printer.

Failed Print
Failure to print or error message that sometimes appears, sometimes can be solved by turning off the printer, then remove the power cord for at least ten minutes. After that, insert the power cable to the terminal, then turn on the printer and try printing again. This way can overcome the failure to print properly.
Readmore »» How To Longer Age Printer

How To Cleaning the Laser Printer

Cleaning the laser printer can solve minor problems that often arise when printing a document, can maintain print quality, printer and extend life. So clean up your printer on a regular basis every time you change the toner or when print quality has begun to decline. Here are the steps to clean a laser printer is right.

Tools and materials needed:
  1. Special cleaning fluid for plastic products.
  2. Water.
  3. Cleaning cloth.
  4. Paper.
  5. Soft toothbrush.

Cleaning Process

Outer Printer Cleaning

  1. Prepare the materials needed to perform the cleaning. (A little water can also help in some cases).
  2. See instructions (printer manual). If the manufacturing company providing cleaning instructions follow the instructions contained therein.
  3. Before you start cleaning off the printer first and pull the electrical connection from the terminal.
  4. Dampen a cloth with cleaning fluid cleaning or making sure enough water is not too wet
  5. Wipe the outside of the printer, make sure no water or cleaning fluids entering into the inside of the printer.
Cleaning the Inner Printer
  1. Disconnect the electrical connection printer.
  2. Remove the paper from the printer tray.
  3. Remove the printer toner Lay on paper.
  4. Clean the inside of the toner with a dry cloth and gently brush with a soft toothbrush.
  5. Clean the parts in the printer carefully. Do not tear the sensitive printers.
  6. Clean the dust remaining inner the printer.
  7. Clean the roller but do not touch the sponge roller.
  8. Enter the toner back if I still want a new toner is used or if the old has gone.
Cleaning With Software
  1. Open the printer software from the shortcut utility program or open a document select Print from the File menu.
  2. From the printer software for the Options, Troubleshooting, Toolbox, Printer Utilities, or that if has the same meaning.
  3. Follow the instructions on the screen.
Readmore »» How To Cleaning the Laser Printer

Tips to buy a laser color printer


Color laser printers are increasingly smaller physique, rushed in print, and cheap price. You can get a price ranging from U.S. $ 300. Therefore, one should pay attention to the color laser printer is not just the price of the affordable unit, or the speed of printing and paper tray capacity. But also the operational costs. Remember, the price of consumables is high.

Because it's possible the color laser printer is a low-end price in the range of U.S. $ 500 in the end be more costly than clever in price range of U.S. $ 500 - U.S. $ 1000 or more due to the speed, capacity larger paper: cost per page becomes cheaper.

For example, if EP316 Black toner for Canon's Laser Shot LBP50550N/5050 sold U.S. $ 78 and can be used to print 2300 pages, meaning the cost per page printing monochrome (not including the price of paper) on the color laser printer is 3.4 U.S. cents.

Meanwhile, black toner for brother EP302 Black, Canon Laser Shot LBP5970, sold U.S. $ 150 with a capacity of 10,000 printed pages. That is, monochrome printing costs per page (outside the paper) with Canon Laser Shot LBP5970 to 1.5 U.S. cents, or about 44% cheaper. But in terms of unit price, Canon Laser Shot LBP5050N the 8ppm color print speed, and can be connected to the network is far below the Canon Laser Shot LBP5970 ($ 520 vs. U.S.. U.S. $ 3600).

So what to look for when going to buy a color laser printer? Here are some consideration.

Speed
Before buying any printer, used to count how many pages are printed each month your office. After that, examine the engine speed and monthly duty cycle of the printer you are considering, to see whether your use pattern in accordance with printer capabilities.

Printer engine speed, expressed in pages per minute (ppm - page per minute) tells how fast the printer to work in ideal conditions (or even the special conditions created by its vendor).

Canon Laser Shot LBP5050N/5050 for example, capable of printing 8ppm for color or 12ppm for black and white. While Canon Laser Shot LBP5970 can drag almost four times: 30ppm to 32ppm for color or black and white on A4 paper. Speed Canon Laser Shot LBP5970 slowed as printing on paper that is wider, the size of A3: 15ppm for color and monochrome.
The average printer, according to tests conducted by PCWorld, reaching only 75% of the maximum speed is mentioned. Even according to PCWorld, the speed of color laser printer is the cheapest way below its vendor claims.
But still the engine speed is the easiest guide to find out if the printer can handle your daily printing needs - personal or in the office. More and more people are using the printer, the more you print, so the faster the printer should do. Except if you like girl talk near the printer with fellow colleagues, looking at who the print jobs come out ahead.

Thorough also how fast a laser printer to respond to your commands perform tasks from the state printing die or standby mode. There are several printers that must warm up first before you can print. As a result you have to wait a while - could be a matter of seconds or even minutes - first.
Why? In most conventional laser printer, there is usually a roller fixing the entire surface must be heated first before printing can begin to do. This is what causes the heating time (warm-up time) that can be quite long - depending on the extent of the surface of the roller.
But there is also, like the Canon Laser Shot LBP5050N/5050 and Canon Laser Shot LBP5970, who claimed zero warm-up time, aka do not require warm-up time. If any, time is very minimal.

This is because all Canon laser printer uses Canon's On-Demand Fixing. Here, a thin fixing film heated directly by a ceramic heater. Because direct heat transferred to the fixing film, the print process can be done without waiting for another warm-up time. Live press the Print button, and instantly print out the results. With On-Demand technology Fixing, according to Canon, Laser Shot LBP5970 Laser color it only takes about 7.5 seconds to be ready to print from the printer activation button (standby mode) lit.
In addition to the print speeds and warm-up response time, precise duty cycle is also a printer. Duty cycle or duty cycle determine the manufacturing threshold for the maximum number of pages printed per month. You'll want a wide range between minimum and maximum mold so freely in print.
Entry-level printers typically have a duty cycle of 300,000 pages per month. Printer at a price of around U.S. $ 1000 duty cycle typically offer an average of 60,000 pages per month, while the weight class printers, high volume, which cost in the range of U.S. $ 1000 - U.S. $ 2000, offering an average of 100,000 pages per month.


Print Resolution
Actually, we need an optical resolution of a fuss about the printer, the exact number of dot per inch that can be printed? Probably not. Color laser printer is the cheapest one is showing an optical resolution of 600 × 600 dpi, which is suitable for most business needs.
Many vendors are also implementing specific algorithms to emulate higher resolutions, such as Canon Laser Shot LBP 50550N/5050 offers a maximum resolution of 9600 × 600 dpi through techniques AIR (Auto Image Refinement). But some, like the Canon Laser Shot LBP 5970, which was offered resolution 1200 × 1200 dpi true.
But if you do not really want the print quality is excellent, just ignore the higher resolution. Moreover, you must be prepared to wait longer to get the results printed.
Which is also an important factor considered is the cost per page to operate the printer. Consumable printer includes all the specification that tells how many pages will be printed by the unit. Depending on what you print, the number you get will be different.
Color laser printers are usually cheaper mengemaskan small capacity toner cartridge - only tolerate a few thousand pages to print. Canon Laser Shot LBP5050/5050N for example, providing EP316 Black toner is resistant to print 2300 pages, and EP316 CMY (cyan-magenta-yellow) with the capacity of each print 1500 pages.

Toner prices are generally expensive, so if you can save, print in color Save. If printing color can not be avoided, then you need a machine that its toner cartridge can print more pages; so the cost per page is lower, and of course do not have to be replaced often. Canon EP302 Toner Laser Shot LBP5970, have the capacity to print 10,000 pages black, while for the color magenta, yellow, and cyan each bear print until 6000 pages,
In most color laser printers (especially low-end), the toner cartridge is included toner, imaging components and toner remaining in the reservoir in a closed place. While supporting the practicality of daily operations, such as the design is actually more expensive in the long run, because all the parts you need to replace at once.
On some printers, particularly high-class models, these components are separated. Just did a new install takes skill and finesse, but in the long term operational costs will be cheaper. Examples include Canon's Laser Shot LBP 5970 drum cartridge offers CMYK EP302, respectively 40,000 page print capacity.
Note that some upper-class printers are now bundling low-capacity toner cartridge, which is labeled as a "starter". For example Canon Laser Shot LBP5050N/5050. Starter toner CMYK packaging his own capacity 'only' 800 pages, while the standard-capacity print until 2300 pages (black), and 1500 pages (CMY). Starter toner usually do give a yield less than half the replacement cartridge / normal. Therefore, try to ask for a bonus toner cartridges at a discount when buying a laser printer.
Paper Handling
The great difference between the color laser printer located in his handling of paper - the number and size. The main paper tray on the printer cheap (under U.S. $ 500) usually accommodates a maximum of 250 sheets of paper. Often no available option to add additional paper tray. In addition, these printers are generally not able to handle paper larger than legal - the only way to do this is to use the manual feed tray, like the Canon Laser Shot LBP5050N/5050.
For printers with a more expensive price, available paper trays for up to 600 sheets of paper (midrange), or even nearly 1200 pieces on a higher model. Canon Laser Shot LBP5970 offers a tray (feeder cassette) optionally up to three levels, each power capacity 500 sheets, so that in total (including the standard tray with a capacity of 100 sheets) this color laser printer can accommodate up to 2000 sheets of paper.
Paper tray on midrange models almost always receive a paper letter and legal sizes. Wide format printer or A3 as Canon Laser Shot LBP5970 can receive a tabloid-size paper, suitable for printing booklets. Besides the size of A3 and A4, Canon Laser Shot LBP5970 quite flexible in accepting other varieties of paper sizes: B4, B5, Letter, EXE. Legal, as well as paper and card with a thickness that varies:
Check also if the printer can print on photo paper, transparencies, stickers sheet CD / DVD, or envelope. Usually manual tray feedback should be used to print the job.
Color Accuracy
All the color laser printer is equipped with calibration feature to check the consistency of color. This order prints to 20 of your brochure will be the same color as the first printing. High-end printers to do the calibration after 40 to 50 copies; other printers do after printing a few hundred copies.
Color is also determined by the toner you use. Each vendor printer toner always recommend the use of the same brand to brand printers for color accuracy and permanence of age use the printer. And more and more available third-party toner is cheaper.

Memory
All users want speed printer would print a hurry and of course the excellent print quality. Print speed, especially for printing in large numbers, are also influenced by the memory (RAM) from the printer itself. Higher dikemaskan memory in a laser printer, usually the better (read: fast printing process).
However, this does not mean that a laser printer should always pack large amounts of memory. There's a printer that can share the task of printing those with memory from a PC connected to the printer. So although the data should be printed large and complex, such as charts or maps of the room of an area, the process can still be printed in a high speed without the need to add more memory to the printer. Because the printer will print with the task of dividing the PC memory.
Models Canon color laser printers are usually adopted this technique, which it’s called the Canon Ultra Fast Rendering II (UFRII) and Load Balancing Technology. Canon ordained nine seconds as the length of time for printing a color document with a high level of complexity at a resolution of 9600 × 1200 optimized dpi for the printer model Canon Laser Shot LBP5970 this packed default memory of 256MB DDR SDRAM. But of course if you want and order to boost the speed faster, you are welcome to add additional memory / optional, such as 512MB.

Save Energy
In the global economic situation is still in shock, is also important to choose a laser printer that is not wasteful electric power. Indeed in the offices or even homes, laser printers are usually more often unemployed (idle), and instead print continuously without stopping. Because it is important to choose a laser printer is the electrical minimum intake while in this idle condition.
One can glance, especially if the print needs of your office include A4 and A3 paper - color or monochrome - is Canon Laser Shot LBP5970. In the sleep mode (sleep), this printer requires only 1W of power intake, which according to Canon's 96% smaller than similar models from rivals brands.
Warranty
Do not forget to ask for warranty card to the printer that you buy. Ask also if the printer return policy is corrupt or jammed.

Other Features

Oh yeah, try to create a specification comparison table from a laser printer that you want to buy. Do not forget to include also the price of the printer unit and its toner prices. This is necessary for you to know what you can get from a particular brand and model, and whether it will meet your printing needs today and also in the future. There is no laser printers are made identical, so you do have to very careful in doing the specifications and price comparisons.
Compatibility for example, need to be given special attention. All laser printers that have been circulating today is not a problem when dealing with computers that Microsoft Windows operating bersistem. But check whether the laser printer is also compatible with other operating systems: Apple Macintosh and Linux.
Network capabilities and management of long-distance (remote) and ease of maintenance becomes something important, especially if the color laser printer will be operated in any office, ranging from small scale to medium scale up. The existence of port USB 2.0 Hi-Speed is required specifications. Also it would be nice if it was embedded 10Base-T/100Base-TX connector, and supporting applications to facilitate network management.
Readmore »» Tips to buy a laser color printer

How to Refill a Toner Cartridge?

While most of us dread any type of office machinery, the computer printer seems to be the biggest monster of all. When a printer keeps spitting out paper when it is not supposed to, eating the paper, or spitting out blank pages when you are in the middle of printing, you have a problem. It can mean you have run out of toner. Replacing a toner cartridge can be expensive, up to a hundreds of dollars; therefore you may want to refill your toner cartridge.
Here is how to refill your toner cartridge:
1. Before you refill your ink toner cartridge, make sure you know the type of toner you need. Getting the wrong toner can make the difference between a working or non working printer. When purchasing a toner refill kit, make sure you have the right model number or type of cartridge. If you are not sure, ask a store employee to help you find proper toner kit that will go with your cartridge. Each toner cartridge is made to work with a particular weight, grain size, and chemical type of toner, and will not work with anything different.
2. Once you get your kit, you will want to clean the machine before you put the toner back in its place. Then make sure that any rollers where the toner cartridge goes are clean and free from any residue from the previous toner. Keeping it clean can make a big difference in the performance of the machine and less problems with toner.
3. From your kit you should transfer that “ink” into your empty toner cartridge, sometimes referred to as a hopper, then reseal the hole with the supplies from the kit. Give it a little shake and place the cartridge back into the printer. Refill kits for cartridges where one has to burn a fill hole will come with specific aluminum tape which you will use to tape over the hole
4. One toner cartridge should only be reused up to two or three times before the need to purchase a brand new toner piece. It is important to note that newer toner cartridges have ’smart chips’ or fuses which have to be replaced in order for the cartridge to perform past its ‘expected’ life.
When refilling your ink toner cartridge, it is important to make sure you are refilling it over an old towel so you do not accidentally get ink on anything of value. As well, wear gloves and an old shirt to avoid any messy ink getting on you. Since it can be costly to purchase the cartridge itself, maintaining the ones you have is cost efficient and more reliable. Some companies will come and pick up the old toner cartridges and others you need to send back. Most companies, like Staples, offer recyclable programs so that it doesn’t harm the environment.
Because toner cartridges are so expensive, refilling the toner cartridge can save you a lot of money. It is also good for the environment because you are reusing your cartridge, thereby conserving resources and keeping used cartridges out of landfills.

Readmore »» How to Refill a Toner Cartridge?

Sunday, August 9, 2009

Translate your Website / Blog in Various Languages

You want the world you website/ blog?
Your website/blog can be translated in different languages? This is one way to increase the number of visitors. Who knows there are people who do not know the language you want to see or are interested in our blog. Chinese at this time have been widely used throughout the world, in gatget is also included. By using google translate, your blog now can translated in many languages. You can see examples Gatget on the left side of my blog, using google, can translate directly posted on a blog we have to go through without a browser. Language translation that I prepare for you for more over 40 languages, namely: Indonesian, Arabia, Bulgarian, Chinese (Simplified), Chinese (Traditional), Croatian, Czech, Danish, English, Finnish, French / French, German, Greek, Indian, Italian, Japanese, Korean, Netherlands, Norwegian, Polish, Portuguese, Romanian, Russian, Spanish, Swedish, and more language..
You want to install in your blog's side bar?
Download the script here (translate), extract zip file and open with your text editor, replace the url "http://whisnusa.blogspot.com/" with the URL of your blog.
Then go to your blogger dashboard layout select a Gatget / new widget, select HTML / Javascript, give title and copy paste the script you have to change the URL of your own. Or you want to use google translator (without flag) like this below:?



Please copy scripts below:
<script src="http://www.gmodules.com/ig/ifr?url=http://www.google.com/ig/modules/translatemypage.xml&up_source_language=auto&w=160&h=60&title=&border=&output=js"></script>

Enter to the side bar widget
Readmore »» Translate your Website / Blog in Various Languages

Friday, June 26, 2009

Tips: Using Resetter Software for Epson Printer without Change Date Setting

Some software resetter or adjustment program for epson are need date setting at computer to use the software without error. sometime change date setting in computer very disturb. In fact there are some ways to use software resetter or adjustment program for epson without changing date setting in computer and without error.

This step :
A. Using bat file or Create bat file

Create one bat file and copy this code. You can use notepad to create it. Place the bat file at the same folder with the adjustment program.
@echo off
echo %date% > currdate.txt
date 11-07-09
rd C:\adjust~1 /s/q
REG DELETE HKEY_LOCAL_MACHINE\SOFTWARE\EPSON\PTSG\ /f
start/wait AdjProg.exe
date < currdate.txt
del currdate.txt
rd C:\adjust~1 /s/q
REG DELETE HKEY_LOCAL_MACHINE\SOFTWARE\EPSON\PTSG\ /f

Note : replace red font with date setting for adjutment program.

B. Using Date Cracker Software:

* Download and install Date Cracker and run the software.
* Click Add button, enter program description (example: Resetter Epson C92)
* Click “…” button the select the adjutment software then click open.
* Type date setting for the adjustment program in the simulated run date.
* Click run button to run the software.


All this methods has been tested

Date Cracker Software Download

Readmore »» Tips: Using Resetter Software for Epson Printer without Change Date Setting

Thursday, June 25, 2009

Lamp projectors reset

Some projectors require the user to reset the lamp hour counter in order for the new lamp to become active.
Please note these are guidelines only, for complete installation instructions please consult your projector's manual.

SONY
• Turn off the projector.(connect powercable, projector off)
• Press the "RESET" button on the remote control and then press channel Left and then press channel Right.
• Press Enter buttom.
• Turn on the projector

3M
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button.
• Your lamp counter will now be reset.

ASK
There are two common methods to reset the lamp counter on these projectors:
Method 1:
• Press the decrease volume button on the remote and then the increase volume button within 3 seconds.
• The LED light on the projector will turn green.
• Turn on the projector.
Method 2:
• Turn on the Projector.
• Open the standard menu using the remote.
• Then select "Setup" or "Service" depending on your projector model.
• Then select "Reset Lamp Timer"
BenQ
• Turn on the projector
• While the projector running, press the MENU button.
• Select "OPTION" on the menu using the 5/6 buttons, then press the ENTER button.
• Select the "LAMP TIME" using the 5/ 6 buttons, then press and hold the RESET button for 3 seconds.
• Select "RESET" using the 5 button.

Boxlight
• Turn on the projector.
• Press the "MENU" button and the on-screen menu will appear.
• Press 3/4 button to remove the red frame pointer to the Setting Menu Icon .
• Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button.
• The message "Reset Lamp Counter?" appears. Move the pointer to "" and then press SELECT button.
• Another confirmation dialog box appears and select "" to reset the Lamp Replace Counter.

Canon
• Turn on the projector.
• Press the "MENU" button and the on-screen menu will appear.
• Press 3/4 button to remove the red frame pointer to the Setting Menu Icon .
• Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button.
• The message "Reset Lamp Counter?" appears. Move the pointer to "" and then press SELECT button.
• Another confirmation dialog box appears and select "" to reset the Lamp Replace Counter.

Christie
• Turn on the projector.
• Press the "MENU" button and the on-screen menu will appear.
• Press 3/4 button to remove the red frame pointer to the Setting Menu Icon .
• Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button.
• The message "Reset Lamp Counter?" appears. Move the pointer to "" and then press SELECT button.
• Another confirmation dialog box appears and select "" to reset the Lamp Replace Counter.

Dell
• Press "MENU" on the remote or control panel to open the on screen display menu.
• Use the 3/4 keys and the section called "Lamp Setting"
• Use the 5/6 keys to select "Lamp Reset"
• Select "YES"
Dukane
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button.
• Your lamp counter will now be reset.

Eiki
• Turn on the projector.
• Press the "MENU" button and the on-screen menu will appear.
• Press 3/4 button to remove the red frame pointer to the Setting Menu Icon .
• Press the 6 button to move the red frame pointer to the Lamp Counter Reset item and then press SELECT button.
• The message "Reset Lamp Counter?" appears. Move the pointer to "" and then press SELECT button.
• Another confirmation dialog box appears and select "" to reset the Lamp Replace Counter.

Elmo
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button.
• Your lamp counter will now be reset.

Hitachi
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button.
• Your lamp counter will now be reset.

HP
• Press "MENU" on the remote or control panel to open the on screen display menu.
• Use the 3/4 keys and the section called "Lamp Setting"
• Use the 5/6 keys to select "Lamp Reset"
• Select "YES"

Infocus
There are two common methods to reset the lamp counter on these projectors:
Method 1:
• Press the decrease volume button on the remote and then the increase volume button within 3 seconds.
• The LED light on the projector will turn green.
• Turn on the projector.
Method 2:
• Turn on the Projector.
• Open the standard menu using the remote.
• Then select "Setup" or "Service" depending on your projector model.
• Then select "Reset Lamp Timer"

Liesegang
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button.
• Your lamp counter will now be reset.

NEC
• Press the "OFF" or "HELP" button on the remote control for a minimum of 10 seconds while in standby mode.
• When the lamp clock is reset to zero the status indicator light will go out.

Optima
• Press "MENU" on the remote or control panel to open the on screen display menu.
• Use the 3/4 keys and the section called "Lamp Setting"
• Use the 5/6 keys to select "Lamp Reset"
• Select "YES"

Panasonic
• Press the "POWER" button until an image is projected onto the screen.
• Press the "MENU" button to display the main on screen menu and then press the F/G buttons to select "OPTION".
• Press the "ENTER" button to display the "OPTION" menu, and then press the 5/6 buttons to select "LAMP RUNTIME".
• Press and hold the "ENTER" button for approximately 3 seconds.
• The "LAMP RUNTIME" will change to "TIME RESET [POWER OFF]".
• The projector will then be powered down.

Panasonic (pt-m1e)
• Press the "POWER" button until an image is projected onto the screen.
• Press the "MENU" button to display the main on screen menu and then press the F/G buttons to select "OPTION ".
• Press the "ENTER" button to display the "OPTION" menu, and then press the 5/6 buttons to select "LAMP RUNTIME /LIFE RUNTIME".
• Press and hold the "ENTER" button (REMOTE) for approximately 3 seconds.(panel will be show RED)
• The "LAMP RUNTIME" will change to "TIME RESET [POWER OFF]".
• The projector will then be powered down.

Proxima
There are two common methods to reset the lamp counter on these projectors:
Method 1:
• Press the decrease volume button on the remote and then the increase volume button within 3 seconds.
• The LED light on the projector will turn green.
• Turn on the projector.
Method 2:
• Turn on the Projector.
• Open the standard menu using the remote.
• Then select "Setup" or "Service" depending on your projector model.
• Then select "Reset Lamp Timer"

Toshiba
• Turn on the projector
• While holding down "ON/STANDBY", "MENU" and "INPUT" simultaneously, plug the power cord into the mains outlet
• The lamp timer is reset automatically
• Check that “ 0H” appears on the lamp timer of the status display.
• NOTE : after resetting the lamp timer , turn off the projector using the “ON/ STANBY” buttom,then turn off the main power switch.

Viewsonic
• Turn on the projector.
• Press the "RESET" button on the remote control for approximately 3 seconds until a dialog box is displayed.
• Select the "RESET" using the button
Readmore »» Lamp projectors reset

Reseting Canon Printer Procedure

Canon Waste Ink Tank Reset Procedure :

Canon GENERIC "S" SERIES
Waste Ink Counter Reset.
(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWER button, plug in electric cord.

(3) Release the RESUME button, Next press and release the RESUME button two (2) times in succession.
Note: you are still holding the POWER button). The printer's carriage will "reset" or move momentarily. If the above was properly performed the printer will enter the "Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp will alternate (change) color with each key press.

1. Service/Factory test printout, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

Canon i320, i255
Waste Ink Counter Reset:
Step 1 : Manual for service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.
3. The indicator (LED) should be green.
4. Press and release the RESUME button , the indicator (LED) should be orange.
5. Press and release the RESUME button again, the indicator (LED) should be green.
6. Release both buttons.
step 2 : Software for Permanant
1. Reconnect the printer cable.
2. Open General Tools software and select (USB PORT)
3. Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode Pls use software for permanent reset"

Canon PIXMA iP1000
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
step 2 : Software for Permanant
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode. Use software for permanent reset"

Canon PIXMA iP1500
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
step 2 : Software for Permanant
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
Remark "After service mode Pls use software for permanent reset"

Canon i850, i950, S600
Start with the printer OFF
1. Hold down RESUME and then hold down POWER
2. release RESUME
3. press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

Canon S450 Printer
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
7: Press Power to set data

Canon BJC1000Series

1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.
5: Press the RESUME once within 5 seconds and release the RESUME .
6: Press and HOLD RESUME for two seconds or more and release it.
7: Press and HOLD RESUME for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-2000 BJC-2100 Series
1: Remove the Cartridge
2: Unplug the AC Power Cord
3: Close Front access panel
3: Hold down the RESUME/RESET button and plug in the AC power cord
4: Release RESUME/RESET after plugging in the AC Power cord.
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .
6: Press and HOLD RESUME/RESET for two seconds or more and release it.
7: Press and HOLD RESUME/RESET for two seconds or more and release it.
8: Unplug AC Power Cord to set data.

Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265
Canon BJC-4100 BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650
Unplug Power Cord
Hold POWER and RESUME buttons
Plug in Power Cord
Release buttons
Open front door of printer
Hold the CARTRIDGE and RESUME buttons
Press POWER
Release all buttons after the beeps
Press CARTRIDGE once
Press RESUME
Canon BJC-5000
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
Canon BJC-5100 Self Test
Switch Printer off. Hold Power for 1 beep.
Waste Counter Reset
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be GREEN.
6: Press Power to set data
Service Test Print
1: Power off printer
2: Press and hold RESUME then press POWER, The indicator will start blinking.
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.
6: Press Power to Print
Nozzle Print
1: Power off printer
2: Press and POWER, until the printer beeps and release.
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.

Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500

1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.
3: Hold POWER and release RESUME
4: Press RESUME twice
5: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.
6: Press Power to set data
Canon BJC-600 BJC-600e BJC-610 BJC-620
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons
3: Plug in Power Cord
4: Release after the beeps
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord
4: Release buttons after the printers starts up
5: Hold CARTRIDGE and RESUME
6: Press POWER
7: Release all buttons after the beeps
8: Press CARTRIDGE 16 times
9: Press RESUME
10: Unplug the Power cord

Canon BJ-30 BJC-35v BJC-70
F14 Error Reset
1: Unplug adapter
2: Hold POWER
3: Plug in ADAPTER
4: Release POWER after printer starts
5: Hold FF and MENU and press POWER
6: Release after beeps
7: Press <> Cartridge until 1A is displayed
8: Press ONLINE
9: Press POWER to shutoff printer
10: Unplug printer then re-plug printer
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520
Turn off the printer.
Press and hold the RESUME button, then press and hold the POWER button.
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.
You are now in Service mode.
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
1. service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA iP3000 above,
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Canon S900, S820, S750, S520
1. Turn off the printer.
2. Press and hold the RESUME button, then press and hold the POWER button.
3. While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.
4. The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.
5. Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.

1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)

6. After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a restart.

Canon S9000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.

Canon MPC190
Reset Waste Ink
1) Enter SERVICE MODE.
By pressing Menu, Copy, Scan, Copy, Copy
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [Set] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.
Readmore »» Reseting Canon Printer Procedure

HP maintenance and reset

Clear the HP Maintenance Service Message :

HP Printer type IIISi :
Press ONLINE until the light goes off
Hold down MENU until PCL CONFIG MENU appears
Press the MENU key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press ENTER/RESET MENU key to turn message off, the * should appear, then press ONLINE
HP 4Si Printers:
Press ONLINE until the light goes off
Press MENU until CONFIG MENU appears
Press the ITEM key until SERVICE MSG=ON* appears
Press the + or - key to change display to SERVICE MSG=OFF
Press the ENTER key to turn message off, the * should appear, then press ONLINE

HP 5Si printers:
Press MENU key 4 times for CONFIG MENU
Press ITEM to display SERVICE MESSAGE=OFF
Press ENTER
Press ONLINE

HP 4000/4050/4100/5000 Printers:
Turn the printer off
Hold down the left side of the ITEM and VALUE +/- keys, turn the printer on and wait until RESET MAINTENANCE COUNT is displayed and then release the keys

HP 4500/4550 Printers:
Turn the printer off
Hold down the CANCEL JOB and SELECT keys and turn the printer on, then wait until the display goes blank and the three LED's come on
Press the right side of the MENU key, then press the SELECT key
You will enter SERVICE MODE after the normal test completes
Press the ITEM key until the FUSER MAINTENANCE COUNT appears
Press VALUE +/- to change to zero
Press SELECT to save
Press GO; the printer should return to READY

HP 8000/8100/8150 Printers:
Press the MENU button until the display reads CONFIGURATION MENU
Press the ITEM button until the display reads SERVICE MESSAGE = ON/OFF
Select OFF*
Press SELECT to save
Turn printer off
Hold the VALUE MINUS and ITEM MINUS buttons while turning the printer back on Hold buttons down until display reads RESET MAINT/COUNTand then release both buttons

HP 9000 Printers:
Turn the printer off
Press and hold the CHECK key
Power on the printer
Release the CHECK key after all three lights come on The display should read SELECT LANGUAGE
Press the up arrow until MAINTENANCE KIT is displayed, then press the CHECK key again and the maintenance kit count has been reset

HP Color LaserJet 4500/4550 Printers (TRANSFER KIT RESET):
Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until TRANSFER KIT SELECT IF DONE is displayed
Press the SELECT button
HP Color LaserJet 4500/4550 Printers (FUSER KIT RESET):
Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until FUSER KIT SELECT IF DONE is displayed
Press the SELECT button
Press the GO button to return to READY

HP Color LaserJet 4600 Printer (IMAGE TRANSFER KIT (ETB) RESET):
After Maintenance is performed, the display should read NEW TRANSFER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW TRANSFER KIT and select

HP Color LaserJet 4600 Printer (FUSER KIT RESET):
After Maintenance is performed, the display should read NEW FUSER KIT =
Press the down arrow to highlight YES, then press the CHECK button to reset Or enter CONFIGURE DEVICE in menus, choose RESETS then RESET SUPPLIES, choose NEW FUSER KIT and select

HP Color LaserJet 8500/8550 Printers (TRANSFER KIT RESET):
Press the MENU button until the RESETS MENU is displayed
Press the ITEM button until RESET TRANSFER LIFE COUNT is displayed
Press the SELECT button to reset, then GO to return to READY

HP Color LaserJet 8500/8550 Printers (FUSER KIT RESET):
Press the MENU button until the RESETS MENU is displayed
Press the ITEM buton until RESET FUSER LIFE COUNT is displayed
Press the SELECT button to reset
Press the GO button to return to READY
Readmore »» HP maintenance and reset

Error code Canon IP1200, IP1300, IP1700, IP1880, IP1980

This is the error code printer Canon IP1200, IP1300, IP1700, IP1880, IP1980.
light blink Indicator:
3x orange 1x Green = mekanik error
4x orange 1x green = absorber full /reset with software tools
5x orange 1x green = cartirdge black/colour error
7x orange 1x green = cartirdge black/colour error
8x orange 1x green = absorber full / reset with software tools
12x - 17x orange 1x green = cartridge detection error
DOwnload resetter
Readmore »» Error code Canon IP1200, IP1300, IP1700, IP1880, IP1980

Resetter Printer Canon IP1880


To reset manually Ink Full Tank, you can try this methods :
1. Turn on Printer Canon iP 1880
2. Push and Hold resume button about 2 minutes
3. Release resume button
4. Printer will back in normal again
5. Then use the software to reset permanent ---> reset tool Download


just for this program resetter, resetter can also use this type for the printer canon Ip 1100, 1800, 2500, 1880, 1980.
Using this software easily, check the "eepRom Clear" and "Cleaning". Then in the options Tab Clear Waste Ink Counter, select the "Platen" and "Main" to reset the indicator into position 0.
On this software, Ip1980 was known as the 1800 ASA. By knowing the type id printer, make it easier to reset the printer select with lock release button, and set the destination IP to ASA in 1800 (only for the printer ip 1980) -> printer is different settings, by pressing the button to end the set. If successful indicator cartridge go to full, but sometimes no effect. To find out more about your printer, you can select the "device id". Tab to "Set Destination" to adjust your printer type. If the facility is non-active means that your printer type not support this mode.
Readmore »» Resetter Printer Canon IP1880

Reset MP390 Waste Ink Full Tank


1)Printer on, press Additional Functions, Scan, Copy, Scan
Now you should be in service mode from there for waste ink tank reset

2)Select Test mode which is like the last avalabe selection
3)Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button

The menu will now say EEPRON Clear
Select Ink count which is option (0) and press set

Then press Stop/Reset Followed by the power button and then wait for it to restart.
Readmore »» Reset MP390 Waste Ink Full Tank

Wednesday, June 24, 2009

Adjustment Program for Stylus C40UX ,C40SX, C20UX, C20SX C61 C62


1. Operating Environment: Windows95 OSR2.0 or higher and Windows98.
(for Windows95)LPT1-LPT3 are used.
(for Windows98)LPT1-LPT3 and EPUSB1-EPUSB3 are used.
2. How to use the Adjustment Program:
Copy the Adjustment Program on the desktop, and then, execute the program.
3. Cautions:
1) When you confirm the function of USB port properly, you must use Windows98
pre-installed PC. It cannot function properly on Windows95.
2) When you operate this program on the Windows95 or Windows98, you cannot
operate it with Status Monitor is running. Close Status Monitor on Task tray
before start the Adjustment Program.
3) Do not change the setting for “Font size” in “settings tab” of the
“Display Property”window.
4) Please do not start the Adjustment Program before connecting the printer with a parallel I/F cable or USB I/F cable. If you do not follow the instruction, the program will freeze.
5) Please do not send any commands during Check Pattern printing.
6) In case of turning off the printer, or the parallel I/F cable or USB I/F
cable is removed during booting the Adjustment Program, please restart the Adjustment Program.

Adjustment Program for Stylus C40UX / C40SX / C20UX / C20SX : Download
Adjustment Program for Stylus C61/C62: Download
Readmore »» Adjustment Program for Stylus C40UX ,C40SX, C20UX, C20SX C61 C62

Sunday, June 21, 2009

howto refill a printer cartridge without ink(at your home)!

Warning, this is a spoof video. The ink level indicator is controlled by the green computer chip. Doing anything else on the cartridge itself (as shown in the video), will not change the ink level. Be careful.
Readmore »» howto refill a printer cartridge without ink(at your home)!

Resetter Epson Stylus C91, C92

Service Adjustment Program



To reset waste ink pad counter epson C91 or epson C92 printers you have to:
- Run the program
- Choose Particulare Adjustment Mode - Choose Waste Ink Pad Counter
- Press INITIALIZE!
Here it is! The waste ink counter resets to ZERO!

Resetter C91- C92 : Download
Readmore »» Resetter Epson Stylus C91, C92

Resetter Epson Stylus C90 Software






















This resetter Software for Epson printer C90. Reset your waste ink pad counter. If any question you can ask to me how to run Adjustment Program. Thank you. and Happy RESET!!
Note : tell your friend about my site. Maybe your friends is very needed.
Download Link
stylus photo C90 Version Indonesia download
Readmore »» Resetter Epson Stylus C90 Software

Reset Ink Counter/Level Canon iP1000













This printer is low budget, the one that I like most is the fast printing.
The problem that I have when using this printer is when the ink waste absorber is full, and he start to blink. Ok guys, Here's some tips for you who still use this printer.

How to physically change the ink waste absorber? Pixma ip1000
The waste ink absorbers can be found at the bottom of the printer case.
Normally you'll have to open the printer case, loose the screws of the print unit and remove the hole print unit from the lower part of the printer case.

4 step to Reset waste ink tank counter CANON PIXMA iP 1000
STEP 1:- Disconnect printer from AC power
STEP 2:- Press and HOLD the POWER button, and connect printer to AC power
STEP 3:- release the the POWER button
STEP 4:- Press the POWER button again

If your IP1000 Blinking try this Tips :

Step 1: Manual for Service mode
1. Unplug POWER and USB cables.
2. Open door, PRESS and HOLD the POWER button.
3. Connect the POWER cable.
4. Close door, then release POWER button.
5. Power ON your printer a usual (It should not blinking anymore)

Step 2 : Software for Permanent
1. Reconnect the USB cable and turn ON your Printer
2. Open "General Tools for iP1500", Downloadh The Software here
3. Select (USB PORT)
4. Choose CLEAR WASTE INK COUNTER - MAIN
5. Choose CLEAR WASTE INK COUNTER - PLATEN
It should be working, coz my printer now work normally

Notes. Before you decide to reseting the waste ink counter, you should really clean up the ink absorber, or else you will find the ink waste absorber overflow.
Readmore »» Reset Ink Counter/Level Canon iP1000

Resetting Epson Stylus C58, Software


This Epson C58 most of them are modifing because the refill ink are often makes trouble
Download here and more resetter for another epson printer in here
















You can also reset and fix your Epson R270, R240, R250, R220, RX700, RX600, RX3700, RX3800, CX1500, CX2800, C63, C79, CX3900, C59, C45, CX4100, R1800, CX5900, C90.

Some tips if you still get error after changing the date:
1. delete folder ;C:\Adjustment Program\Stylus C58
2. delete registry HKEY_LOCAL_MACHINE\SOFTWARE\EPSON\PTSG\Stylus C58
delete the folder registry not just the key
3. Don't forget to set the date into 9 Nop 06 before running the program
Readmore »» Resetting Epson Stylus C58, Software

TUTORIAL RESETTER PRINTER EPSON STYLUS T11

Before using the Software Resetter Epson Stylus T11, make sure:

a. Driver Printer Epson Stylus T11 already installed first, and make sure the printer is connect to the computer

b. Make sure you have the "Software Resetter Printer Epson Stylus T11".

c. Make sure that the damages requested in the printer reset counter (usually the printer lights all glowing red)

Before using the Software Resetter Epson Stylus T11, change the settings on your computer so that the program resetter Epson T11 may be the way without any error.

To change, click Start - Control Panel - Date and Time (Classic View for the model). if you model the Control Panel Category View, select Date, Time, Language and Regional Options, then select Date and Time settings to change the date.

The computer date to 11 April 2008


Here are step by step to do the reset the Waste Ink Pad Counter Epson T11:

1.Download Software Resetter Printer Epson Stylus T11.
2. Resetter Epson T11 extract it.
3. Turn on the printer.
4. AdjProg.exe Run the file and click Accept.
5. Select a particular adjustment mode.
6. Continue by selecting the Waste Ink Counter pad and then click OK.
7. Click the Check button, to read the Waste Ink Counter Pad, and wait until the reading is completed.
8. Click initialization to reset waste ink pad counter to 0 and click Finish.
9. Turn off the printer, wait a while, and then turn the printer back.
10. Wait until the printer completes the process of calibration, and printer will be normal again.
11. Continue with Printer Test Page.
Download resetter t10 - t11

Download resetter t11
Readmore »» TUTORIAL RESETTER PRINTER EPSON STYLUS T11

Saturday, June 20, 2009

Manually Reset For Epson Stylus Color Printer

EPSON Stylus Color
Pressing and holding ALT+FONT+LOAD+PAUSE buttons combination, press POWER button.
Release all buttons.

EPSON Stylus Color 440, 640, 740, 460, 660, 670, 760, 860, 880, 1160

Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button, until all leds will blink.

EPSON Stylus Color 680
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold LOAD/EJECT button, until all leds will blink.

EPSON Stylus Color 800, 850
Pressing and holding LOAD, CLEANING Color and CLEANING Black buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and release CLEANING Color button, You will see leds blinking.

EPSON Stylus Color 900, 980
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button, You will see blinking INK OUT led.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button for 10-12 seconds.

EPSON Stylus Photo 785, 895
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Error led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.

EPSON Stylus Photo 890, 1280, 1290
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.
In 2-3 seconds time press LOAD/EJECT and CLEANING buttons again.

EPSON Stylus Color 3000
Pressing and holding PAUSE, LF/FF and DOWN ARROW buttons turn on printer.
Release all buttons.

EPSON Stylus Color 300
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons
In 2-3 seconds time press LOAD/EJECT and CLEANING buttons again.

EPSON Stylus Color 400, 600
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and release LOAD/EJECT button.

EPSON Stylus Color 440, 640, 740, 460, 660, 670, 760, 860, 880, 1160
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button, until all leds will blink.

EPSON Stylus Color 800, 850
Pressing and holding LOAD, CLEANING Color and CLEANING Black buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and release CLEANING Color button, You will see leds blinking.

EPSON Stylus Color 900, 980
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button, You will see blinking INK OUT led.
Release all buttons.
In 2-3 seconds time press and hold CLEANING button for 10-12 seconds.

EPSON Stylus Photo 785, 895
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Error led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.

EPSON Stylus Photo 890, 1280, 1290
Pressing and holding Maintenance and Roll Paper buttons, press POWER button, You will see blinking Power led.
Release all buttons.
In 2-3 seconds time until led is blinking press and hold for 10-12 seconds Roll Paper button, until all leds will blink.

EPSON Stylus Color 680
Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds.
Release all buttons.
In 2-3 seconds time press and hold LOAD/EJECT button, until all leds will blink.
Readmore »» Manually Reset For Epson Stylus Color Printer

Service Utility for Epson Stylus Printers.

SSC Service Utility allow you to do many amazing things with Your Epson printer :
1) Work directly with CSIC in Epson Stylus printers cartridges.
2) Reset or rewrite any chip using special addon device.
3) Freeze internal ink counters.
4) Reset internal ink counters even with empty cartridges.
5) Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode.
6) Hot swapping of cartridges supported.
7) Resetting of protection counter (even then it is already full).
8) More then 100 different Epson printers supported
This allow many people with high printing demands to save some money (program works with both black and color cartridges).
Up to day this software works under Windows 95/98/ME/2K2/XP with both the LPT and USB printers.

NOTE ! You can lost Epson lifetime guarantee on print head by refilling ink cartridges!

Program screenshots:









Epson Model/type supported :
Epson Stylus Сolor 400 supported
Epson Stylus Сolor 440 supported
Epson Stylus Color 480 LPT supported
Epson Stylus Color 480SXU / 580 supported
Epson Stylus Сolor 600 supported
Epson Stylus Сolor 640 supported
Epson Stylus Сolor 660 supported
Epson Stylus Сolor 670 supported
Epson Stylus Color 680 / 777 supported
Epson Stylus Сolor 740 supported
Epson Stylus Сolor 760 supported
Epson Stylus Сolor 800 / 850 supported
Epson Stylus Сolor 860 supported
Epson Stylus Color 880 supported
Epson Stylus Color 900 / EM-900C supported
Epson Stylus Color 980 supported
Epson Stylus Сolor 1160 supported
Epson Stylus Color 1520 supported
Epson Stylus Color 3000 supported
Epson Stylus C20 / C40 / CL-750 supported
Epson Stylus C41 / C42 / C43 / C44 / C45 / C46 / C47 / C48 ** supported
Epson Stylus C50 supported
Epson Stylus C60 supported
Epson Stylus C61 / C62 ** supported
Epson Stylus C63 / C64 ** supported
Epson Stylus C65 / C66 and PE ** supported
Epson Stylus C67 / C68 / D68 and PE ** supported
Epson Stylus C70 ** supported
Epson Stylus C80 ** supported
Epson Stylus C82 ** supported
Epson Stylus C83 / C84 ** supported
Epson Stylus C85 / C86 and PE ** supported
Epson Stylus C87 / C88 / D88 and PE ** supported
Epson Stylus Photo RX420 / RX425 / RX430 ** supported
Epson Stylus Photo RX500 / RX510** supported
Epson Stylus Photo RX520 ** supported
Epson Stylus Photo RX600 / RX610 ** supported
Epson Stylus Photo RX620 ** supported
Epson Stylus Photo RX700 ** supported
Epson Stylus CX3100 / CX3200 ** supported
Epson Stylus CX3500 / CX3600 / CX3650 ** supported
Epson Stylus CX3700 ** supported
Epson Stylus CX3800 / CX3810 / DX3800 ** supported
Epson Stylus CX4500 ** supported
Epson Stylus CX4600 ** supported
Epson Stylus CX4100 / CX4200 ** supported
Epson Stylus CX4700 / CX4800 ** supported
Epson Stylus DX4200 / DX4800 ** supported
Epson Stylus CX5100 / CX5200 ** supported
Epson Stylus CX5300 / CX5400 ** supported
Epson Stylus CX6400 / CX6600 ** supported
Epson Stylus CX6300 / CX6500 ** supported
Epson Stylus CX7800 ** supported
Epson PictureMate supported
Epson Stylus Photo supported
Epson Stylus Photo EX supported
Epson Stylus Photo 700 / IP-100 supported
Epson Stylus Photo 750 / PM-770C supported
Epson Stylus Photo 780 / 790 / PM-780C supported
Epson Stylus Photo 810 / 820 supported
Epson Stylus Photo 820 ** supported
Epson Stylus Photo 825 / 915 supported
Epson Stylus Photo 830 / 830U ** supported
Epson Stylus Photo 870 / PM-875DC supported
Epson Stylus Photo R200 / R210 ** supported
Epson Stylus Photo R220 / R230 ** supported
Epson Stylus Photo R300 / R310 ** supported
Epson Stylus Photo R320 ** supported
Epson Stylus Photo R800 / PX-G900 ** supported
Epson Stylus Photo R1800 ** supported
Epson Stylus Photo R2400 ** supported
Epson Stylus Photo 890 supported
Epson Stylus Photo PM-890C supported
Epson Stylus Photo PM-A700 ** supported
Epson Stylus Photo PM-G720 ** supported
Epson Stylus Photo PM-970C ** supported
Epson Stylus Photo 895/ 785EPX supported
Epson Stylus Photo 900 ** supported
Epson Stylus Photo 925 / 935 ** supported
Epson Stylus Photo 950 / 960 / PM-950C ** supported
Epson Stylus Photo 1200 / PM-3000C supported
Epson Stylus Photo 1270 / PM-3300C supported
Epson Stylus Photo 1280 / PM-3500C supported
Epson Stylus Photo 1290 supported
Epson Stylus Photo 2000P supported
Epson Stylus Photo 2100 ** supported
Epson Stylus Photo 2200 / PM-4000EPX ** supported
Epson Stylus Pro 5000 / PM-5000C supported

Latest versions changes:

New in 4.30:
- support for R270
- support for R240
- support for R340
- support for CX2800
- support for CX3900
- support for CX4900
- support for CX5900
- support for C58/C59
- support for RX640
- improved support for C2100/2200
- improved support for RX700
- improved support for R2400
- improved support for 785EPX/825/895/915
- some other improvements and bug fixes

New in 4.20:
- support for CX4200/CX4700/CX4800/DX4200/DX4800
- support for C47/C48
- support for RX430
- support for CX6500/CX6300
- improved support for CX6400/CX6600
- improved support for RX500/RX510
- improved support for RX600/RX610
- improved support for R1800
- improved support for CX3700/CX3800/DX3800/DX3850
- improved support for C67/C68/D68
- improved support for C87/C88/D88
- many new chip models supported
- some other improvements and bug fixes

New in 4.10:
- support for PM-970C
- support for PictureMate
- support for RX700
- support for R2400
- support for PM-A700
- support for PM-G720
- support for RX520
- support for CX7800
- support for CX4100
- support for DX3800
- support for CX3800/CX3810
- support for CX3700
- support for C67/68 and Photo Editions
- support for C87/C88/D88 and Photo Editions
- support for R220/R230
- support for R320
- support for CX4500
- support for CX3650
- various bug fixes

New in 4.00:
- ability to work with additional reset device
- support for CX4600
- support for CX5300
- support for CX5100
- support for RX420
- support for RX425
- support for RX620
- support for R1800
- improved support for almost all other printers
- improved ink freezer
- improved ink monitor, implemented status information
- protection counter reset improvements
- various bug fixes

Reset using SSC serve software :
* Run and install SSC software.
* Run setting in the printer model section and equalto the printer the close the setting.
* Right click mouse on ssc icon in the system tray, select “protection counter” then click “reset protection counter”, Ok.
* Turn off the printer the turn on again, and the printer should be Ok



Download v4.00
Download v4.30
Direct link Download v4.30

Note :
This is freeware project, so it is illegal to take money for this software.

Source : www.ssclg.com
Readmore »» Service Utility for Epson Stylus Printers.